Dynojet Snowmobile Dynos: Installation Guide Uživatelský manuál

1 - 6 Document #98260100 Step 9Fit the cover into position and check clearances.The Lift Handle on the back of

Document #98260100 1 - 7Dyno MaintenanceThe dyno should get a general inspection every 2weeks depending on the number of runs

1 - 8 Document #98260100 The cover should be removed every 300 runsto ensure the brake is properly adjusted (se

Document #98226100 Master 2 - 1Chapter 2Hardware InstallationDynoWare EX+The standard dynamometer electronics package iscomprised of 4 interconnected

2 - 2 Master Document #982261002 - 2 Master Document #98226100RPM Module:The RPM module receives and processes signalsfrom up to 2 inductive pickups f

Document #98226100 Master 2 - 3Document #98226100 Master 2 - 3Dynamometer Input/Output Module:The dynamometer I/O module sends and receivesdata from t

2 - 4 Master Document #982261002 - 4 Master Document #98226100CPU Module:The CPU module contains a 32-bit processorwhich acquires data from the expans

Document #98226100 Master 2 - 5Document #98226100 Master 2 - 5CPU Module: ... ContinuedThis connector provides a synchronization signalto a 3rd-part

2 - 6 Master Document #982261002 - 6 Master Document #98226100Remote SwitchBreakout Board toDynoWare CableCord from Power SupplyPrimary Inductive Pick

Document # 98260100 3-1Chapter 3Optional Accessories Installation Several optional accessories are available for theDynojet Dynamometer. Ca

©1993-1999 Dynojet Research, Inc. All Rights Reserved.Installation Guide for Snowmobile Dynamometers.This manual is copyrighted by Dynojet Research,

3-2 Document # 98260100Contents(A) - Driver Carriage Frame(B) - Front Mount Assembly (C) - Rear Mount AssemblyDriver Carriage Set upStep 1The pins on

Document # 98260100 3-3Step 2Mount the Rear Carriage Mount to the CarriageFrame with the (6) 3/8” allen head bolts. Thebacking plates tha

Application #1- Polaris- Yamaha- Ski Doo / Bombardier- Arctic CatRear Carriage Mount should oriented so that 4out of the 6 holes are towards the front

Document # 98260100 3-5Installing the Driver CarriageStep 1Remove the rear suspension as per manufacturersinstructions.Step 2Due to the v

3-6 Document # 98260100Step 4 Now that you have the adjustable rods removed,loosen the locking nuts on the rods.Adjust the length on the rods equally

Document # 98260100 3-7Step 6Install the front Driver Carriage mount in the twomost forward (towards engine) holes in thetunnel.If there i

3-8 Document # 98260100Step 7Retract the spring pins in the Driver Carriage,and then position it in the front mount. Releasethe spring pins when you

Document # 98260100 3-9Step 9The track should be hanging loose at this point,you will need to pre-tension the track with theDriver Carriage

3-10 Document # 98260100Tighten the center adjuster bolt to pre-tension thetrack. Tighten the (6) bolts that hold the rear mount onthe Driver Carria

Document # 98260100 3-11Step 11Reverse the procedure to remove the DriverCarriage, and replace the suspension permanufacturers instructions

Document #98260100 1iContentsChapter 1 ...1 - 1Setup and Maintenan

1ii Document #98260100

Document#98260100 1 - 1Chapter 1Setup and Maintenance of the Sled DynoUncrating the dynoStep 1Look for any external

1 - 2 Document #98260100 The crate will contain the following.1 - box containing:2 - (A) inside driver wheels a

Document #98260100 1 - 3Step 4Remove all components except the dyno andcheck the contents.Step 5Remove bolts holding down the

1 - 4 Document #98260100 DO NOT LIFT THE DYNO BY THE ARMS !Step 7Install the jack with the pin and cotter keys

Document #98260100 1 - 5Install the front (2) screws. These screws areaccessed from the inside of the brake cover.(Leave the